When a renovation is on the table, or a new appliance is going in, or a garage is getting a proper workshop setup, the electrical side of the job needs to be figured out before the first wall opens up. Getting the panel capacity, the circuit routing, and the code requirements sorted at the start keeps the rest of the project on track. We handle that planning work for homeowners and contractors in Norcross, and we handle the repair calls that come in alongside it. We cover the full range of residential and commercial electrical work in this area, available every day from 7:30 AM to 11:00 PM.
Norcross is a small city with a real mix of housing, from older homes that were built before modern electrical standards to newer construction and commercial properties that need circuits sized for current loads. That range shapes what we do here. Older properties come with their own set of considerations, including knob-and-tube wiring, aluminum branch circuits, and panels that were never sized for the loads a modern household puts on them. Newer builds and tenant spaces have different demands. We work through both.
When the power goes out or behaves strangely, the first practical question is where the fault sits. A partial outage, where half the house loses power but the other half is fine, usually points to a problem on one leg of the incoming service. That is a utility issue, and the fix belongs to them. A full outage that only affects one property while neighbors are unaffected is a different story, and it may sit anywhere from the meter base to the main breaker to a wiring fault inside the home.
We trace the fault to find where our side ends and the utility's begins. If the problem is on their side, we tell you that clearly and explain what to report to them and how. If it is on our side, we scope the repair on the call, confirm the cost, and schedule the visit. Either way, you get a straight answer rather than a bill for work that was never ours to do.
Finding work that was done incorrectly is more common than people expect, especially in a place where homes have changed hands a few times or had additions put on over the years. The question when we open up a wall or a panel is not whether something looks unfamiliar, but whether it is safe, whether it meets the code inspectors here actually enforce, and whether it can carry what the circuit needs to carry.
Wiring that is undersized for its load, connections that were not made properly, and devices that were installed without the right protection all get corrected as part of the job. Arc-fault and ground-fault breakers are often missing in circuits that were installed before those requirements existed, and adding them is a straightforward correction. Work in this area gets done to the code inspectors here actually enforce, and that standard applies to corrections as much as to new work.
Not everything that looks old is a problem. Wiring that was installed correctly for its time and is still in good condition may not need to be replaced, even if it is older. Aluminum wiring in branch circuits is a different matter. It requires remediation, not because it is always dangerous as installed, but because the connections it was made with were not designed for it and the combination creates real risk over time. Knob-and-tube wiring that is still in active use, especially in areas where insulation has been added around it, generally needs to come out. We explain what we find and why before any work starts.
A new appliance, a hot tub, or a piece of workshop equipment that draws serious power needs its own dedicated circuit sized for that load. Running a dryer or a range off a shared circuit is a problem waiting to happen. We size the circuit correctly, run the wiring, and install the right outlet or disconnect for the equipment involved. That includes 240V circuits for larger loads and the panel capacity check that has to happen before the circuit is run.
An intermittent problem is often harder to pin down than a straightforward failure, because it does not show itself on demand. A breaker that trips only under certain conditions, or a circuit that loses power occasionally and then comes back, takes methodical tracing rather than a quick swap. We work through the circuit from the panel out, check connections, load, and device condition, and find where the fault is actually sitting before anything is replaced.
Low-voltage work covers doorbell wiring, data runs, and the rough-in that structured wiring needs before walls close up. This comes up most often during renovations, when the opportunity to run wiring inside walls is available before drywall goes back. We handle the rough-in and the connections so that the finish work is clean and the devices work the way they are supposed to.
A detached garage or a workshop that needs real electrical capacity needs its own subpanel fed from the main panel. Running everything back to the house on a single circuit is not practical once you have more than a light and an outlet to power. We size the subpanel for what the space actually needs, run the feed from the main panel, and install the circuits inside the outbuilding from there.
Workshop equipment that draws high amperage needs a circuit built for it. A welder or a large compressor on an undersized circuit will trip breakers, damage the equipment, and create a wiring hazard over time. We confirm the load requirement, check the panel capacity, and run a dedicated circuit that can carry what the equipment actually draws. If the panel needs more room first, that conversation happens before the circuit is run.
Appointments are confirmed on the call, once the job is scoped and the price is agreed. We work around the schedule of whoever needs to be there, including tenants and businesses that cannot shut down for a full day. For a rental property where a tenant is in place, we coordinate the visit around their availability. For a commercial space that has to stay open, we work out which circuits can be isolated without taking the whole building down.
When something will not keep, call and tell us what is happening. A sparking outlet, a burning smell, or a breaker that will not reset are situations that move to the front of the line. We take short-notice calls when the schedule allows, and we confirm what is available when you reach us. For what the job actually entails, the full electrical services list lays it out.
Most repair and installation work only requires the circuit being worked on to be de-energized, not the whole panel. Replacing an outlet, adding a circuit, or correcting a wiring fault in one part of the house does not mean the rest of the property loses power. We isolate what needs to be isolated and leave everything else running.
Panel work is different. Replacing a breaker panel or upgrading the service entrance requires a full shutdown for the duration of that work. That is not avoidable, but it is plannable. We confirm the scope and the expected duration on the call before anything is scheduled, so a household working from home or a business with equipment that needs to stay powered can make the arrangements that make sense for them.
For properties where a full shutdown would cause a real problem, we talk through the timing before the visit is booked. Early morning starts, weekend scheduling, or a phased approach where different parts of the work are done on separate visits are all options worth discussing. The goal is to get the work done without the power-off period landing at the worst possible time.
The cost of an electrical job depends on what the job actually involves, and that is not something that can be settled without knowing the specifics. The things that move a quote are the nature of the fault, what has to be opened up to reach it, and whether the existing circuit or panel can carry what the change requires. A circuit addition in a panel with room to spare is a different scope from one that needs a panel upgrade first. A wiring fault that traces back to a single loose connection is a different job from one that requires a section of wiring to be replaced inside a finished wall.
When you call, we go through what you are dealing with and ask the questions that let us give you an accurate price before anything is booked. The price is confirmed before the visit is scheduled, and the scope is explained so you know what the job covers. Ask what the price includes and you get a direct answer. That is the process on every call.
We cover Norcross and the communities around it throughout Gwinnett County, including Peachtree Corners, Berkeley Lake, Doraville, Lilburn, and Duluth. If your address is in or near this part of the county, call and we will confirm coverage when you reach us.
Yes. The process is the same regardless of which community in the area you are calling from. You call, we scope the job, confirm the price, and schedule the visit. Coverage for Peachtree Corners, Berkeley Lake, Doraville, Lilburn, Duluth, and the rest of Gwinnett County works the same way as a Norcross call. If you are unsure whether your address is in the service area, call and we will confirm it on the spot.
Homes in this area that were built before the 1980s sometimes still carry aluminum branch-circuit wiring or knob-and-tube systems, and both require specific remediation rather than standard repair. Panels installed under older codes may also be undersized for the load a modern home carries, particularly if the house has had additions or major appliances added since the original installation. An electrical safety inspection is a practical starting point for any older home before a renovation or a sale, because it identifies what needs attention before the work starts.
We check the service entrance, the meter base, and the panel first, then work outward through the affected circuits. If the evidence points to a fault on the utility's side of the meter, we tell you that directly and explain who to contact. The utility is responsible for the service up to the meter, and we are clear about where that line is.
Changes after rough-in require opening the walls in the affected areas and re-running the circuits. That is more involved than making the change before the walls close, and the cost reflects it. We flag this at the scoping stage so the plan is settled before rough-in begins wherever possible.
You do not need to know what the problem is before you call. Describing what is happening, where it is happening, and when it started is enough for us to scope the job and give you a price.
Call (943) 292-6289 every day from 7:30 AM to 11:00 PM.
We handle the diagnosis, the repair, and the cleanup. Pick up the phone. Get a straight answer. That is how we work.
Close by, we also take electrical work in: Doraville, Lilburn, Tucker, Mountain Park, Clarkston.
We handle the full range of electrical work for Norcross homeowners, landlords, and businesses, from a single outlet repair to a complete service upgrade. Every job starts with a call where we scope the work, explain what it involves, and give you a price before anything is scheduled. The rows below cover what each service includes, who it fits best, and what is useful to know going in.
Call (943) 292-6289 to get started.
| Electrical Service | What It Covers | Best For | Worth Knowing |
|---|---|---|---|
| EV Charger Installation | 240V dedicated circuit installationPanel capacity checkHardwired charger or 240V outlet setupPanel upgrade coordination if needed | Homeowners adding an electric vehicle and needing a reliable Level 2 charging setup at home | Installation starts with a panel capacity check. If the panel is near its limit, a service upgrade may be part of the scope. We confirm both on the call. |
| Breaker & Fuse Repair | Breaker replacement and testingFuse panel assessmentCircuit load evaluationPanel interior inspection | Homes where a breaker trips repeatedly or a fuse blows under normal load | A breaker that trips once after an obvious overload is doing its job. One that trips repeatedly under normal use points to a circuit or wiring issue worth diagnosing. |
| Electrical Panel & Service Upgrades | Load calculation and service sizingPanel replacement and breaker installationService-entrance and meter coordinationSubpanel installation for garages and workshops | Homes with a 100-amp service, a full panel, or breakers that trip under normal load | A panel upgrade typically requires utility coordination for the meter side of the job. We handle the permit and inspection process as part of the work. |
Call (943) 292-6289 to go over the job, get a price, and find out what the visit covers before anything is scheduled.
(943) 292-6289